Person:

Alvarenga, Jack

Ice repellent coatings have been studied and keenly sought after for many years, where any advances in the durability of such coatings will result in huge energy savings across many fields. Progress in creating anti-ice and anti-frost surfaces has been particularly rapid since the discovery and development of slippery, liquid infused porous surfaces (SLIPS). Here we use SLIPS-coated differential scanning calorimeter (DSC) pans to investigate the effects of the surface modification on the nucleation of supercooled water. This investigation is inherently different from previous studies which looked at the adhesion of ice to SLIPS surfaces, or the formation of ice under high humidity conditions. Given the stochastic nature of nucleation of ice from supercooled water, multiple runs on the same sample are needed to determine if a given surface coating has a real and statistically significant effect on the nucleation temperature. We have cycled supercooling to freezing and then thawing of deionized water in hydrophilic (untreated aluminum), hydrophobic, superhydrophobic, and SLIPS-treated DSC pans multiple times to determine the effects of surface treatment on the nucleation and subsequent growth of ice. We find that SLIPS coatings lower the nucleation temperature of supercooled water in contact with statistical significance and show no deterioration or change in the coating performance even after 150 freeze-thaw cycles.

We report a simple method to pattern wetting properties on thin films of periodic mesoporous organosilica (PMO). A hydrophobic methane PMO thin film was covered by masks and exposed to oxygen plasma to make the unmasked area hydrophilic. The wettability patterns could be revealed only when the films were immersed in water or exposed to moisture. We expect that our method would extend the utility of PMO to such areas as sensing and information security.

Inspired by the long-term effectiveness of living antifouling materials, we have developed a method for the self-replenishment of synthetic biofouling-release surfaces. These surfaces are created by either molding or directly embedding 3D vascular systems into polydimethylsiloxane (PDMS) and filling them with a silicone oil to generate a nontoxic oil-infused material. When replenished with silicone oil from an outside source, these materials are capable of self-lubrication and continuous renewal of the interfacial fouling-release layer. Under accelerated lubricant loss conditions, fully infused vascularized samples retained significantly more lubricant than equivalent nonvascularized controls. Tests of lubricant-infused PDMS in static cultures of the infectious bacteria Staphylococcus aureus and Escherichia coli as well as the green microalgae Botryococcus braunii, Chlamydomonas reinhardtii, Dunaliella salina, and Nannochloropsis oculata showed a significant reduction in biofilm adhesion compared to PDMS and glass controls containing no lubricant. Further experiments on vascularized versus nonvascularized samples that had been subjected to accelerated lubricant evaporation conditions for up to 48 h showed significantly less biofilm adherence on the vascularized surfaces. These results demonstrate the ability of an embedded lubricant-filled vascular network to improve the longevity of fouling-release surfaces.

The stability and longevity of surface-stabilized lubricant layers is a critical question in their application as low- and nonfouling slippery surface treatments in both industry and medicine. Here, we investigate lubricant loss from surfaces under flow in water using both quantitative analysis and visualization, testing the effects of underlying surface type (nanostructured versus flat), as well as flow rate in the physiologically relevant range, lubricant type, and time. We find lubricant losses on the order of only ng/cm2 in a closed system, indicating that these interfaces are relatively stable under the flow conditions tested. No notable differences emerged between surface type, flow rate, lubricant type, or time. However, exposure of the lubricant layers to an air/water interface did significantly increase the amount of lubricant removed from the surface, leading to disruption of the layer. These results may help in the development and design of materials using surface-immobilized lubricant interfaces for repellency under flow conditions.

The deep building layouts typical in the U.S. have led to a nearly complete reliance on artificial lighting in standard office buildings. The development of daylight control systems that maximize the penetration and optimize the distribution of natural daylight in buildings has the potential for saving a significant portion of the energy consumed by artificial lighting, but existing systems are either static, costly, or obstruct views towards the outside. We report the Dynamic Daylight Control System (DDCS) that integrates a thin cast transparent polydimethylsiloxane (PDMS)-based deformable array of louvers and waveguides within a millimeter-scale fluidic channel system. This system can be dynamically tuned to the different climates and sun positions to control daylight quality and distribution in the interior space. The series of qualitative and quantitative tests confirmed that DDCS exceeds conventional double glazing system in terms of reducing glare near the window and distributing light to the rear of the space. The system can also be converted to a visually transparent or a translucent glazing by filling the channels with an appropriate fluid. DDCS can be integrated or retrofitted to conventional glazing systems and allow for diffusivity and transmittance control.

Passive anti-icing surfaces, or icephobic surfaces, are an area of great interest because of their significant economic, energy and safety implications in the prevention and easy removal of ice in many facets of society. The complex nature of icephobicity, which requires performance in a broad range of icing scenarios, creates many challenges when designing ice-repellent surfaces. Although superhydrophobic surfaces incorporating micro- or nanoscale roughness have been shown to prevent ice accumulation under certain conditions, the same roughness can be detrimental in other environments. Surfaces that present a smooth liquid interface can eliminate some of the drawbacks of textured superhydrophobic surfaces, but additional study is needed to fully realise their potential. As more attention begins to shift towards alternative anti-icing strategies, it is important to consider and understand the nature of ice repellency in all environments to identify the limitations of current solutions and design new materials with robust icephobicity.

This research introduces a novel approach to control light transmittance based on flexible polydimethylsiloxane (PDMS) films that have been plasma-treated such that micro-scale surface features have a visual effect as the film responds to applied strain. The effect is continuously tunable from optically clear (71.5% Transmittance over a 400-900 nm wavelength) to completely diffuse (18.1% T). Changes in the film's optical properties are triggered by bi-axial strains applied using a pneumatic system to form pressurized envelopes. This paper reports on a series of experimental studies and provides system integration research using prototypes, simulations and geometric models to correlate measured optical properties, strain, and global surface curvatures. In conclusion, a design is proposed to integrate PDMS light control within existing building envelopes.

Flexible and stretchable microscale fluidic devices have a broad range of potential applications, ranging from electronic wearable devices for convenient digital lifestyle to biomedical devices. However, simple ways to achieve stable flexible and stretchable fluidic microchannels with dynamic liquid transport have been challenging because every application for elastomeric microchannels is restricted by their complex fabrication process and limited material selection. Here, a universal strategy for building microfluidic devices that possess exceptionally stable and stretching properties is shown. The devices exhibit superior mechanical deformability, including high strain (967%) and recovery ability, where applications as both strain sensor and pressure‐flow regulating device are demonstrated. Various microchannels are combined with organic, inorganic, and metallic materials as stable composite microfluidics. Furthermore, with surface chemical modification these stretchable microfluidic devices can also obtain antifouling property to suit for a broad range of industrial and biomedical applications.